|
 | Arduino Ethernet Shield
from arduino.cc
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Duemilanove and Mega (using the Ethernet library coming in Arduino 0019). An SD card library is not yet included in the standard Arduino distribution, but the sdfatlib by Bill Greiman works well. See this tutorial from Adafruit Industries for instructions (thanks Limor!).
Catalog number: 43133. Brand: arduino.cc. Brand's Part Number: ETHERSHIELD5.
More Product Details ...
|
| | |
|
|
|
|
 | Arduino ProtoShield Kit
from Sparkfun
Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the ProtoShield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level. Catalog number: 46664. Brand: Sparkfun. Brand's Part Number: DEV-07914.
More Product Details ...
|
| | |
|
|
|
|
 | Ardumoto - Motor Driver Shield
from Sparkfun
This is a motor shield for Arduino that will control two DC motors. Based on the L298 H-bridge, the Ardumoto can drive up to 2 amps per channel. The board takes its power from the same Vin line as the Arduino board, includes blue and yellow LEDs to indicate active direction, and all driver lines are diode protected from back EMF. Catalog number: 44792. Brand: Sparkfun. Brand's Part Number: DEV-09815.
More Product Details ...
|
| | |
| Stock Number | Buy | Product Title | Price | Status | |
H04479-01H |
 | Ardumoto - Motor Driver Shield | $24.99 |
In Stock |
|
|
|
|
 | Board of Education Shield
from Parallax
The Board of Education (BOE) Shield makes getting started with the Arduino as easy as they told you it was going to be. The BOE arrives completely assembled and provides the breadboard, power regulation, peripheral connectors and shield pins that are needed for nearly every project but are missing from the basic Arduino design. Catalog number: 47019. Brand: Parallax. Brand's Part Number: 35000.
More Product Details ...
|
| | |
| Stock Number | Buy | Product Title | Price | Status | |
H04701-01C |
| Board of Education Shield | $29.99 |
In Stock |
|
|
|
|
 | Danger Shield
from Sparkfun
The Danger Shield mounts on top of your Arduino to provide a number of useful human interface inputs and outputs including sliders, buttons, buzzers and displays.
Catalog number: 43158. Brand: Sparkfun. Brand's Part Number: DEV-10115.
More Product Details ...
|
| | |
|
|
|
|
 | Gameduino
from excamera
Gameduino is a game adapter for Arduino (or anything else with an SPI interface) built as a single shield that stacks up on top of the Arduino and has plugs for a VGA monitor and stereo speakers. The sound and graphics are definitely old-school, but thanks to the latest FPGA technology, the sprite capabilities are a step above those in machines from the past. The adapter is controlled via SPI read/write operations, and looks to the CPU like a 32Kbyte RAM. (Unlike many 8-bit machines, there are no restrictions on when you can access this RAM). There is even a handy reference poster (which you can download below) showing how the whole system works.
Catalog number: 45187. Brand: excamera. Brand's Part Number: GAMEDUINO.
More Product Details ...
|
| | |
|
|
|
|
 | Joystick Shield Electronic Kit
from Sparkfun
The Joystick Shield kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers. Catalog number: 45179. Brand: Sparkfun. Brand's Part Number: DEV-09760.
More Product Details ...
This is an electronic kit which you must assemble by soldering.This kit cannot be returned once opened.
Click here for our return and warranty policies ...
|
| | |
|
|
|
|
 | Modkit MotoProto Shield
from Sparkfun
The Modkit MotoProto Shield for Arduino that makes it easy to connect up to 4 sensors and control two DC motors as well as a 16X2 character LCD. The sensor jacks accept 2.5mm cables and provide access to VCC, GND, and an analog input.
Catalog number: 44958. Brand: Sparkfun. Brand's Part Number: DEV-10018.
More Product Details ...
|
| | |
|
|
|
|
 | Monster Moto Shield
from Sparkfun
This is essentially a ramped up version of
Ardumoto - Motor Driver Shield. For this monster shield we've replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We've also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for 5mm screw terminals (not included), making it easy to connect larger gauge wires.
Catalog number: 45062. Brand: Sparkfun. Brand's Part Number: DEV-10182.
More Product Details ...
|
| | |
|
|
|
|
 | ProtoScrewShield
from Sparkfun
The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It also has a lot of the utility provided by Arduino Protoshield, including: a large prototyping space of both connected and unconnected 0.1" spaced through-holes, a couple 5V and GND busses, a reset button, general use push button, and a 5mm yellow LED.
Catalog number: 44784. Brand: Sparkfun. Brand's Part Number: DEV-09729.
More Product Details ...
This is an electronic kit which you must assemble by soldering.This kit cannot be returned once opened.
Click here for our return and warranty policies ...
|
| | |
|
|
|
|
 | TellyMate Shield
from Batsocks
The TellyMate Shield equips an Arduino with the ability to send simple text and graphics to a TV. The TellyMate Shield connects to an Arduino board using long headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
Catalog number: 45161. Brand: Batsocks. Brand's Part Number: TellyMate.
More Product Details ...
|
| | |
|
|
|
|
 | USB Host Shield
from Sparkfun
The USB Host Shield contains all of the digital logic and analog circuitry necessary to implement a full-speed USB peripheral/host controller with your Arduino. This means you could use your Arduino to interface with and control any USB slave device - thumbdrives, digital cameras, bluetooth dongles, and much more!
Catalog number: 44990. Brand: Sparkfun. Brand's Part Number: DEV-09947.
More Product Details ...
|
| | |
|
|
|
|
 | Video Game Shield
from Wayne and Layne, LLC
The Video Game Shield is an Arduino add-on shield to make your own video games, including graphics, text, sound effects, and music!
Catalog number: 45195. Brand: Wayne and Layne, LLC . Brand's Part Number: VGS.
More Product Details ...
This is an electronic kit which you must assemble by soldering.This kit cannot be returned once opened.
Click here for our return and warranty policies ...
|
| | |
|
|
